Frequent question: How do you tell the difference between a 904 and 727 transmission

Generally, a 727 shifter lever is straight and a 904 is offset (though some applications have different length of levers to compensate for vehicle model/engine combinations). Remember, only smallblocks have 904 derivative transmissions, though some came with 727’s (i.e. certain truck and HP car models).

How do I tell what year my 727 transmission is?

Year. An A-727 can also be identified as being a 1978 and newer lockup units just by examining the transmission’s input shaft. It was built with a lockup if the shaft is smooth at its last half inch, on the contrary, if it is splined to the end of the input shaft, then it is a non-lockup transmission.

How do I identify my Chrysler transmission?

Look at the transmission from the driver’s side of the vehicle by going under the vehicle at the driver’s-side door. If the transmission is off the vehicle, it is on the left side, when looking from behind the unit and the input shaft is pointing forward.

How do you identify TorqueFlite transmission?

You can easily identify an A-727 by its oddly shaped 14-bolt oil pan. The A-727 uses a paper fluid filter and has two transmission bands, one for reverse, and the other is a kickdown band. All shift ratios were 2.54:1 for first gear, 1.45:1 for second gear and 1.0:1 for third gear.

IT IS INTERESTING:  Do they make a 24 volt trolling motor battery

Will a 727 transmission fit a 318?

a small block 727 will fit a small block 318….

How do I identify my transmission?

Some transmissions may have a code stamped into their case or a tag riveted to them. According to Koval, the easiest way to identify an automatic transmission, though, is by transmission pan shape. “Almost all have their own shape and pan bolt design,” Koval said.

How much does a 727 transmission weigh?

Gearing for the 727 is 2.54:1 for 1st gear, 1.54:1 for second, 1:1 for third and 2.21:1 for reverse. The weight of the transmission is a hefty 161 lbs.

Can you tell what transmission you have by the Vin?

The next six digits to check (positions 4-9) are the vehicle descriptor section. Numbers 4 through 8 describe the car with such information as the model, body type, restraint system, transmission type and engine code. Number 9 is the check digit, which is used to detect invalid VINs.

Who makes Chrysler transmissions?

The current Chrysler 8 and 9-speed automatics are built by the company ZF.

How do I identify my RAM transmission?

Look inside the truck cab on the driver’s side to see if there is a clutch pedal. If there is a clutch pedal, this means that the Dodge Ram has a manual transmission. If there is no clutch pedal, then the truck has an automatic transmission.

What is a 904 transmission?

In 1960, the Chrysler Corporation first introduced the aluminum 904. Its design has mostly evolved from the earlier version of Chrysler PowerFlite, which is a two speed automatic with the cast-iron three-speed TorqueFlite.

IT IS INTERESTING:  How do you remove vape residue from windshield

What is a 46RE transmission?

a 46RH is a newer transmission with a lock up torque converter, and over drive, also Hydraulically controlled (note the H in 46 RH) the 46RE is a transmission with a lock up torque converter, and overdrive, it is electronically controlled (note the E in 46RE) both the 46RH and 46RE are improved variations of the A518.

Will a 727 transmission fit a 360?

You need a flexplate or converter for a 360 to make it work.

Will a 5.7 Hemi bolt up to a 727 transmission?

Yes a smallblock torqueflite will bolt right up to the 3rd gen. Hemis. Mopar Performance sells a flexplate for this application or if you already have a truck flexplate you can use it by removing the starter ring gear slightly modifying the torque converter bolt holes.

Four wheels