Is the 351w a good engine

the 351w is a very good engine, it can handle a lot of power before the block splits, that usually happens at around 800hp. the 351m is an ok engine, good for use in trucks and for the basis of building a good 400. the 351c on the other hand is tough to beat, even by the chevy 350.

How long will a 351 Windsor last?

it all depends on how hard you run it. could go up to 300,000 miles if you never run it over 3000 rpm or it could last another 50 miles if you run it at say maybe 8000 rpm.

How much horsepower can you get out of a 351 Windsor?

The long-lived Ford “Windsor” engine, displacing 351 cubic inches, was available in performance applications such as the Ford Boss Mustang in 1971, and today is available in a crate-engine version which features up to 535 horsepower.

IT IS INTERESTING:  You asked: Is there such thing as a v16 engine

What year is the best 351 Windsor?

Best years

From what I have read, the best year for 351W blocks are 1969, 70, and 71. For some reason these were the strongest 351W ever produced, but very hard to find.

Which engine is better 351C or 351W?

In terms of power, the 351C in stock form was a more potent motor than the 351W in stock form, however either engine can be built up to most requirements. Another alternative to consider is the 351M which is the big block 351 than can be easily modified to a 400 cu-in.

How many miles per gallon does a 351 Windsor get?

the 302 only gets about 15 mpg in city and the 351 gets about 12.

How much does it cost to rebuild a 351 Windsor?

A stock rebuild depends on how much work you do yourself. Since you are asking, I assume you will not do any thing to the engine yourself, so I would expect to pay anywhere from $1000-$1500 for someone to rebuild the engine if you take it out.

Is 302 better than 351W?

So for equal money, a 351 will have more cubes, more low end torque, and a lower RPM peak. A 302 will have the same HP, but a slightly higher tq peak with lower tq numbers. In almost any situation, cubes are better.

What’s the best 351 engine?

The 351W is the one with the better oil system, but it has 3″ mains. The 351/400 Midland is too large you would have too much cutting to fit plus they use a very large bell housing on to trans. The 351 Cleveland will fit, but it would be tight, same goes for the 351 Windsor. The Windsor would be a good choice.

IT IS INTERESTING:  Your question: Are diesel vehicles being phased out

How much power can a stock 351W crank handle?

A stock 351W block will handle around 550hp, maybe a little more with a main girdle. Either way, after 550hp it becomes a track oil down waiting to happen. Seen some with stock cranks and making some serious hp too. Some cars I’m thinking of had to be making 700-800.

Which 351W block is best?

pb_paulie_b. The 69′ block is the strongest stock 351w block. High nickle content and thicker main webbing. It is also flat at the top of the main webbing.

How much horsepower does a 5.8 351W have?

Ford 351W V-8 Specs

Engine: Ford 351W V-8 (5.8L)
Peak Horsepower: • 1969 – 250 hp w/ 2 barrel carburetor, 300 hp @ 5,400 rpm w/ 4 barrel carburetor • 1972 (net power ratings adopted) – 153 hp w/ 2 barrel, 161 hp w/ 4 barrel • 1997 – 205 hp (CA version), 210 hp @ 3,600 rpm • Ford Lightning – 240 hp @ 4,200 rpm

When did Ford stop making the 351 Windsor?

The Windsor (351W) was introduced in 1969 and stayed in use until 1991. The Cleveland (351C) was first used in 1970 on some early-production 1971 models, and was last produced in 1974, when it was replaced with the Modified (351M) model.

Whats the difference between a 351 Windsor and a 351 Cleveland?

Windsor valve covers use 6-bolt covers, whereas the Cleveland/Modified uses 8-bolt covers. Timing Chain. Cleveland/Modified engines have the timing chain recessed into the front of the block itself, and its timing cover is essentially just a flat piece of metal.

IT IS INTERESTING:  What devices use parallel transmission

What is a 351 Cobra Jet engine?

The Q-code 351 “Cobra-Jet” (also called 351-CJ, 351-4V) was produced from May 1971 through the 1974 model year. … This engine was different from the 1970-71 M-code 351C having a more aggressive camshaft, a spread-bore carburetor, a four-bolt block and the lower compression allowed regular fuel to be used.

Will 351 Cleveland heads fit a 351 Windsor?

351C heads will not work on a 351W block without drilling new water jackets in the heads. A 351C intake will not work at all on a 351 W. From what I understand, a Boss 302 intake, not a 351C intake, mind you, will work on a 302, not a 351W, with the modified 351 C heads.

Four wheels