— No, that 351W will not bolt onto your 351M C6. — No, all 351W engines used the 351W bellhousing pattern, shared by the 302, 289, and 300-I6. — Your C6 uses a pattern shared by the 351C, 351M/400M (same engine block), and 429/460.
What transmission goes with a 351 Windsor?
A C-6 can come behind a 351w, it is a good transmission. C4, C6 or AOD will fit.
What engines fit a C6 transmission?
There are four different bellhousings for a C6. The small V8 or windsor family, this includes the 3.8 V6, the 4.9 inline 6, the 289,302, and 351w, 351c (not a windsor built engine, but shares the same bellhousing). Then there is the FE C6, which fits FE only, 3xx to 429.
What vehicles have a 351 Windsor?
History. Ford debuted the 351 Windsor in the 1969 Ford Mustang Mach 1 with both two-barrel and four-barrel carburetor configurations.
How much horsepower does a 351 Windsor put out?
Ford 351W V-8 Specs
|Engine:||Ford 351W V-8 (5.8L)|
|Peak Horsepower:||• 1969 – 250 hp w/ 2 barrel carburetor, 300 hp @ 5,400 rpm w/ 4 barrel carburetor • 1972 (net power ratings adopted) – 153 hp w/ 2 barrel, 161 hp w/ 4 barrel • 1997 – 205 hp (CA version), 210 hp @ 3,600 rpm • Ford Lightning – 240 hp @ 4,200 rpm|
Will a 351 Windsor fit a 302 transmission?
The 302 and 351 are very similar, just as the 351C, 351M, and 400 are similar but they are not interchangeable across engine classes. No, the fact that a C6 transmission which will bolt up to either a 302 5.0L or 351W 5.8L does NOT mean it will bolt up to a 300 I-6 4.9L.
Will a T5 transmission fit a 351W?
The starter, motor plate, starter, and TO bearing should be the same for a 302 or 351W with the T5 set up.
How much is a C6 transmission worth?
$100 – $150 for a C6 sounds about right.
How much HP can a C6 transmission handle?
Yes a c6 will hold 500 hp but not a stock one with 3 high gear clutches or a stock valvebody….
Which transmission is better C4 or C6?
The C4 transmission was primarily used in cars. The C6 transmission could handle more power. Due to the ability to handle more power, the C6 transmission was used in many Ford trucks with bigger engines, and in larger cars that were manufactured with bigger engines.
Is the 351 Windsor a good engine?
the 351w is a very good engine, it can handle a lot of power before the block splits, that usually happens at around 800hp. the 351m is an ok engine, good for use in trucks and for the basis of building a good 400. the 351c on the other hand is tough to beat, even by the chevy 350.
What year 351W is best?
From what I have read, the best year for 351W blocks are 1969, 70, and 71. For some reason these were the strongest 351W ever produced, but very hard to find.
What’s the difference between a 351 Cleveland and a 351 Windsor?
On a Cleveland/Modified engine, the radiator hose (and thermostat housing) sticks vertically right out of the top of the engine block. Windsor engines have the radiator hose and thermostat installed into the intake manifold, where it exits from the front of the engine. Valve Covers.
What’s the best 351 engine?
The 351W is the one with the better oil system, but it has 3″ mains. The 351/400 Midland is too large you would have too much cutting to fit plus they use a very large bell housing on to trans. The 351 Cleveland will fit, but it would be tight, same goes for the 351 Windsor. The Windsor would be a good choice.
Is 302 better than 351W?
So for equal money, a 351 will have more cubes, more low end torque, and a lower RPM peak. A 302 will have the same HP, but a slightly higher tq peak with lower tq numbers. In almost any situation, cubes are better.
How can I get more horsepower out of my 351 Windsor?
351W Performance Tricks
- Flow: The Key to Building Horsepower. The key to making more horsepower in the 351 Windsor, or any engine, is to move more gas/air mixture through the engine. …
- Removing Flow Restriction. A cylinder head flows as well as its most constricted part. …
- Exhaust Headers. …
- Cylinder Head Flow. …
- Interchangeable Heads.